# Some noise fusing points **URL:** \ **Category:** Customer support\ **Created:** [March 26, 2025, 10:40pm UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517 "2025-03-26T22:40:02Z")\ **Posts on this page:** 18\ **Page:** 1
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 26, 2025, 10:40pm UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/1 "2025-03-26T22:40:02Z")
I am getting some noise when I fuse the points only in marker mode or global markers. In Feature mode everything is good. Somebody noticed that? I can see better the scan in the raw preview than after fusing points. (I used a MINI 2 and the latest version of Revoscan). It´s not a calibration issue, it’s something when fusing points. I tried to go to a previous version, but I cannot open the files. Thank you in advance ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 27, 2025, 12:07am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/2 "2025-03-27T00:07:23Z")
Hi @peko You don’t see noises in the preview because it is low resolution preview and not the actual full version. Always mesh the scan based on your fusing settings , if fused for example at 0.5 mm mesh it at the Grid setting of 0.5 mm for best results , setting higher level of meshing than fusing could results in artifacts where additional points are created . Regarding markers, if marker mode give you a bad result , it is indicator that the scanner need to be calibrated . I will forward your issue to the team and try to replicate your bug and let you know about the result ASAP ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 27, 2025, 12:47am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/3 "2025-03-27T00:47:25Z")
Hi PUTV, and thank you for your reply. I didn’t meshed the file. I only fused the points. The scanner doesn’t needs to be calibrated because, I enter in the option of calibration and make the previous test and says that is calibrated, and with feature mode I get better results. Other problem I note is that it takes all the resources of the computer when fusing. I don’t have these problems with feature mode. I think is some kind of bug. I recently updated the program to latest version. Is there any way to fuse the points out of revoscan? or any universal revopoint application? I cannot use previous version, due I have not the piece to scan now. Regards ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 27, 2025, 1:04am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/4 "2025-03-27T01:04:20Z")
Hi @peko If you have issues with resource just fuse it at lower values I will check tonight if there is an issue with the software and MINI 2, and let you know what to do . If it is bug issue we can arrange early version for you if you don’t have it anymore. ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 27, 2025, 1:12am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/5 "2025-03-27T01:12:05Z")
You can see the difference between fused and not fused. In my opinion I can only see clearly the markers (really clear and precise circles made of points). In my opinion could be a bug. I think the image is better in not fused scan. Other problem I had is that after some frames when I am scanning, other ones dissapeared…and I should scan back. Fused ![image](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/d/c/dced0cc7421c4b653e73c880993d2d0ef3c96a42.jpeg) Not fused ![image](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/5/d/5d73f88827def3d25ebc34d4bae9d569df908f04.jpeg) (The marker blocks are not black) ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 27, 2025, 1:28am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/6 "2025-03-27T01:28:15Z")
Ok thank you for the images Did you tried the function clean lose points and overlapped detection after fusing to remove all the overlapped points because that’s what they are ? The preview is just a preview of the frames not an object , it is unorganized preview . Try to clean up the lose isolate points after fusing as that’s what usually everyone is doing after. And don’t suggest yourself with the preview , as it is just virtual preview of how the scan should look.like after fusing and cleaning . Also can you scan the bust that came with using marker mode for reference ? ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 27, 2025, 4:15am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/7 "2025-03-27T04:15:59Z")
Yes, I tried. The results are worse than feature mode. I scanned the bust: Before fusing: ![image](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/9/7/97ff5fe0b22cc00593c875d867a2bbba4f1938f3.jpeg) After fusing: ![image](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/3/b/3b42ef79b8b990803c6b6b420d672f50cdf50d93.jpeg) And as you can see the markers are really good…Could they be maybe very reflective? I have white ones and these ones that are reflective, but both came from Revopoint. ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 27, 2025, 4:29am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/8 "2025-03-27T04:29:17Z")
Yes I can see the bug now very clearly Thank you for testing it out with the bust. The team is going to investigate it and I will give you reply by tomorrow . ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 27, 2025, 4:35am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/9 "2025-03-27T04:35:15Z")
Thank you! Note that I tried to fuse in two computers (both i7 one with RTX 3060Ti and 16Gb RAM Other i7 1050 Ti and 32Gb RAM), and both gave me memory errors. I think that shouldn’t happen, and doesn’t happen in feature mode. In one of them, the program closed. In all ways, I hope that’s just a fusing problem and not scan problem. I use it for professional use, and the piece came back to my customer. ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 27, 2025, 4:56am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/10 "2025-03-27T04:56:33Z")
Don’t worry , if there is any problem with your scanner it will be fixed quick by our technical support team. You not lose anything. ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 27, 2025, 6:06am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/11 "2025-03-27T06:06:55Z")
Do you mean with the scanner or the scans? as explained I don’t have the scanned piece ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 27, 2025, 11:55am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/12 "2025-03-27T11:55:23Z")
The scanner. ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 27, 2025, 10:15pm UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/13 "2025-03-27T22:15:02Z")
Yes, I know. But as explained I think that that’s a fusing error. Any explanation? ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 28, 2025, 2:28am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/14 "2025-03-28T02:28:45Z")
Not yet , the team is still investigating . I will let you know ASAP ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 28, 2025, 11:31pm UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/15 "2025-03-28T23:31:50Z")
I note that fusing points with markers takes too much time, and sometimes freezes my computer. In feature mode verything runs faster. I noted too one time that Acestream opened without any reason during fusing. Could be related? ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 29, 2025, 9:03am UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/16 "2025-03-29T09:03:31Z")
Hi @peko I will be back at work tomorrow evening at 8 pm ET time So we can continue with this issue , the office is closed for the weekend. ---
**Author:** ![peko](https://avatars.discourse-cdn.com/v4/letter/p/c37758/32.png) [@peko](https://forum.revopoint3d.com/u/peko)\ **Post date:** [March 30, 2025, 6:01pm UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/17 "2025-03-30T18:01:29Z")
Ok PUTV. Thank you a lot!! ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [August 20, 2025, 7:42pm UTC](https://forum.revopoint3d.com/t/some-noise-fusing-points/35517/18 "2025-08-20T19:42:35Z")
Hi @peko Sorry I own you an apology but I lost the tread somehow , just found it back. There are upcoming software updates regarding all the issues , so please wait for the new version .