# Revo scan memory consumption **URL:** \ **Category:** Discussions\ **Created:** [December 10, 2024, 12:42pm UTC](https://forum.revopoint3d.com/t/revo-scan-memory-consumption/30817 "2024-12-10T12:42:07Z")\ **Posts on this page:** 6\ **Page:** 1
**Author:** ![rednet](https://avatars.discourse-cdn.com/v4/letter/r/ea666f/32.png) [@rednet](https://forum.revopoint3d.com/u/rednet)\ **Post date:** [December 10, 2024, 12:42pm UTC](https://forum.revopoint3d.com/t/revo-scan-memory-consumption/30817/1 "2024-12-10T12:42:07Z")
is it possible to understand how much memory revo scan can consume for a single project. I have a problem: rendering status fusion points 8268832 model type continuous scan setting high speed 18 fps feature tracking- body Fusion 0.10mm advanced on the pc I have 24 GB ram but at a certain point it goes out of memory and consumes all the pc’s memory ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [December 10, 2024, 5:09pm UTC](https://forum.revopoint3d.com/t/revo-scan-memory-consumption/30817/2 "2024-12-10T17:09:26Z")
It uses it regarding to your processing settings . Use the meshing settings based on fusing 0.1 fusing , use 0.1 Grid for best results 8 millions points can even use 32 GB of RAM for processing What you use for scanning ? And what size is the object ? ---
**Author:** ![rednet](https://avatars.discourse-cdn.com/v4/letter/r/ea666f/32.png) [@rednet](https://forum.revopoint3d.com/u/rednet)\ **Post date:** [December 10, 2024, 5:31pm UTC](https://forum.revopoint3d.com/t/revo-scan-memory-consumption/30817/3 "2024-12-10T17:31:14Z")
I am using POP 3 and I have scanned a person’s half body, I would like to scan the whole person but how much ram would I need what does use 0.1 Grid for best results mean where do I find this setting in revo scan regards ![revoscan](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/5/0/50a63536330ec9445760ea99f7791bb8a8ca0f8f.png) ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [December 10, 2024, 6:20pm UTC](https://forum.revopoint3d.com/t/revo-scan-memory-consumption/30817/4 "2024-12-10T18:20:36Z")
That’s a lot of points for POP3 But the Grid is under the Meshing settings , when you slide it up you will see the Grid size will adjust , make sure you reach 0.1 Grid settings while sliding it up … or less in this case as from my experiences it have lots of points and that will cost good amount of memory to process . ---
**Author:** ![rednet](https://avatars.discourse-cdn.com/v4/letter/r/ea666f/32.png) [@rednet](https://forum.revopoint3d.com/u/rednet)\ **Post date:** [December 10, 2024, 6:45pm UTC](https://forum.revopoint3d.com/t/revo-scan-memory-consumption/30817/5 "2024-12-10T18:45:07Z")
thanks for your reply, I’ve been using scanners for a short time, I also bought a range 2 maybe it’s better for making a body, regarding the emsh but is it the one in the photo? if it’s less than 0.10 I can’t ![2024-12-10 (8)](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/b/2/b21e4dbcb976c4c5f080c87eaafa6460bf49a69c.png) ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [December 10, 2024, 7:59pm UTC](https://forum.revopoint3d.com/t/revo-scan-memory-consumption/30817/6 "2024-12-10T19:59:06Z")
You see POP3 was not made for scanning human bodies , even if you can you need to have proper amount of RAM to process scans like that , this is not the software fault. For full bodies you need at least 64GB of RAM . You see the GRID don’t even allows you to get to higher point to prevent crash of the system . Use lower resolution for meshing around 5 level may help . There is no way around , or you get better system RAM or you will get lower resolution scans .