# Miraco Plus need help **URL:** \ **Category:** MIRACO Series\ **Tags:** miraco\ **Created:** [March 28, 2025, 2:33pm UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601 "2025-03-28T14:33:04Z")\ **Posts on this page:** 17\ **Page:** 1
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 28, 2025, 2:33pm UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/1 "2025-03-28T14:33:04Z")
Hi all! ![image](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/c/4/c482ef9ad5085c0047840c5b8185f2f2e4ba55af.jpeg) Не могли бы вы проконсультировать меня (я думаю, и все буде добре) для создания оптимальных конструкций Fusion и Mesh Construct на MIRACO Plus? Here is an example of Fusion 0.05 and Mesh Construct 0.1. The surface is very noisy. I get the same result on other scans. The only way to get smooth surfaces is to use One-Click Edit, but this mode, as well as Smooth mode, although it produces smooth surfaces, it loses a lot in detail. Thanks! ---
**Author:** ![kkula9999](https://avatars.discourse-cdn.com/v4/letter/k/3ab097/32.png) [@kkula9999](https://forum.revopoint3d.com/u/kkula9999)\ **Post date:** [March 28, 2025, 3:14pm UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/2 "2025-03-28T15:14:45Z")
can you take the picture of the original product? ---
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 28, 2025, 3:20pm UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/3 "2025-03-28T15:20:38Z")
> [@kkula9999](#): > > can you take the picture of the original product? Yes, of course! ![image](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/7/5/75472a496892322d36a5120ea433d7360c7399a9.jpeg) ---
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 29, 2025, 5:13am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/4 "2025-03-29T05:13:33Z")
It doesn’t make any sense. I tried the scan in PC mode, but it’s still scary to look at the scans. I even recalibrated the scanner again. At the same time, other users are doing fine. Can I run any tests on the functionality of the hardware and firmware of the scanner, is everything exactly OK with it? ---
**Author:** ![kkula9999](https://avatars.discourse-cdn.com/v4/letter/k/3ab097/32.png) [@kkula9999](https://forum.revopoint3d.com/u/kkula9999)\ **Post date:** [March 29, 2025, 8:40am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/5 "2025-03-29T08:40:40Z")
could this be the result of dull dark surface? ---
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 29, 2025, 8:53am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/6 "2025-03-29T08:53:32Z")
> [@kkula9999](#): > > could this be the result of dull dark surface? And this? This is the result on all models. Maybe it’s a firmware issue? ![image](https://canada1.discourse-cdn.com/flex029/uploads/revopoint3d/original/3X/c/e/ce237c333ca187b1c41fe115143ca949f6a68f3c.jpeg) ---
**Author:** ![kkula9999](https://avatars.discourse-cdn.com/v4/letter/k/3ab097/32.png) [@kkula9999](https://forum.revopoint3d.com/u/kkula9999)\ **Post date:** [March 29, 2025, 9:42am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/7 "2025-03-29T09:42:19Z")
try to use default value for both fusion and mesh, is it getting better ---
**Author:** ![TheBoatScans](https://avatars.discourse-cdn.com/v4/letter/t/b77776/32.png) [@TheBoatScans](https://forum.revopoint3d.com/u/TheBoatScans)\ **Post date:** [March 29, 2025, 10:59am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/8 "2025-03-29T10:59:37Z")
High speed mode? I haven’t had much luck with it. ---
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 29, 2025, 11:28am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/9 "2025-03-29T11:28:30Z")
> [@TheBoatScans](#): > > High speed mode? I haven’t had much luck with it. In any mode, the picture is identical. ---
**Author:** ![TheBoatScans](https://avatars.discourse-cdn.com/v4/letter/t/b77776/32.png) [@TheBoatScans](https://forum.revopoint3d.com/u/TheBoatScans)\ **Post date:** [March 29, 2025, 11:31am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/10 "2025-03-29T11:31:52Z")
Just to clarify, accuracy mode (high/standard/high speed) has no effect on scanning quality? ---
**Author:** ![ivan](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/ivan/32/16571_2.png) [@ivan](https://forum.revopoint3d.com/u/ivan)\ **Post date:** [March 29, 2025, 5:17pm UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/11 "2025-03-29T17:17:58Z")
Hi! You might using unnecessarily too high meshing settings, which induce noise? A great explanation from @PUTV , which seems related: > [@Scan quality poor?](https://forum.revopoint3d.com/t/scan-quality-poor/23372/8): > > You probably used Standard fusing … use Advanced fusing , it produces beautiful results . My coin was fused at 0.2 in Advanced mode and meshed at 4.3 and the results are perfect , if I fused it at standard 0.05 and meshed at 7 I would get a disk full of sand and no details . You see pointcloud cage is the most important base for you scan … too high meshing can actually induce artificial noises and erase the details . Don’t worry if you fuse the scan at 0.2 in Advanced mode you will not lose a… ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 30, 2025, 1:36am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/12 "2025-03-30T01:36:22Z")
> [@TheBoatScans](#): > > Just to clarify, accuracy mode (high/standard/high speed) has no effect on scanning quality? It is impossible to have the same results in all modes ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 30, 2025, 1:41am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/13 "2025-03-30T01:41:34Z")
Hi @Snakegreen Please contact [customer@revopoint3d.com](mailto:customer@revopoint3d.com) For hardware support It is impossible to have all all results the same in all modes. The other day you posted face and it was looking just fine , so what changed ? Please contact the support as there is nothing I can help you here with . Never push the meshing higher than the fused point cloud to avoid inducing artificial points and with it noises You fused at 0.05 you meshing it at 0.05 I know MetroX is much smoother but that is thanks to Blue Lights Infrared scanners have slightly higher noise level naturally , but not like in your previews . The technical support will help you out ---
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 30, 2025, 3:51am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/14 "2025-03-30T03:51:36Z")
> [@Scan quality poor?](https://forum.revopoint3d.com/t/scan-quality-poor/23372/8): > > You probably used Standard fusing … use Advanced fusing , it produces beautiful results . My coin was fused at 0.2 in Advanced mode and meshed at 4.3 and the results are perfect , if I fused it at standard 0.05 and meshed at 7 I would get a disk full of sand and no details . You see pointcloud cage is the most important base for you scan … too high meshing can actually induce artificial noises and erase the details . Don’t worry if you fuse the scan at 0.2 in Advanced mode you will not lose a… I don’t say anything about coins at all, they don’t work out in principle. The only thing that gives a more or less digestible result is One-Click Edit. But it eats up almost all the detail. It seems to me that I shouldn’t have upgraded. ---
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 30, 2025, 3:53am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/15 "2025-03-30T03:53:03Z")
> [@PUTV](#): > > Please contact [customer@revopoint3d.com](mailto:customer@revopoint3d.com) > > For hardware support > > It is impossible to have all all results the same in all modes. > > The other day you posted face and it was looking just fine , so what changed ? > > Please contact the support as there is nothing I can help you here with . > > Never push the meshing higher than the fused point cloud to avoid inducing artificial points and with it noises > > You fused at 0.05 you meshing it at 0.05 > > I know MetroX is much smoother but that is thanks to Blue Lights > Infrared scanners have slightly higher noise level naturally , but not like in your previews . > > The technical support will help you out Yes, I already wrote, I know that one of the users had a similar problem on the first MIRRACO and help him roll back the firmware there. I hope that it will help in my case too. ---
**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\ **Post date:** [March 31, 2025, 9:22am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/16 "2025-03-31T09:22:50Z")
The best way to check it out , good move , better than guessing ! ---
**Author:** ![Snakegreen](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/snakegreen/32/24866_2.png) [@Snakegreen](https://forum.revopoint3d.com/u/Snakegreen)\ **Post date:** [March 31, 2025, 9:35am UTC](https://forum.revopoint3d.com/t/miraco-plus-need-help/35601/17 "2025-03-31T09:35:23Z")
> [@PUTV](#): > > The best way to check it out , good move , better than guessing ! I’ve already written to support. I sent them a screen recording during scanning and processing, as well as several projects.