# Miraco Far Mode Point Distance

**URL:** <https://forum.revopoint3d.com/t/miraco-far-mode-point-distance/23542>\
**Category:** MIRACO Series\
**Created:** [January 2, 2024, 8:26pm UTC](https://forum.revopoint3d.com/t/miraco-far-mode-point-distance/23542 "2024-01-02T20:26:55Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![TheBoatScans](https://avatars.discourse-cdn.com/v4/letter/t/b77776/32.png) [@TheBoatScans](https://forum.revopoint3d.com/u/TheBoatScans)\
**Post date:** [January 2, 2024, 8:26pm UTC](https://forum.revopoint3d.com/t/miraco-far-mode-point-distance/23542/1 "2024-01-02T20:26:55Z")

</div>

Scanning some large things in far mode today, I noticed that Miraco will fuse at point distances greater than 2mm. Is that coming to desktop Revoscan soon?

---

<div class="post-metadata">

**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\
**Post date:** [January 3, 2024, 1:31am UTC](https://forum.revopoint3d.com/t/miraco-far-mode-point-distance/23542/2 "2024-01-03T01:31:32Z")

</div>

Large things have different resolution and pitch point , it also depends on the volume, you can’t fuse it at lower resolution than the hardware scanned it .

I am guessing you used the Large mode with greater pitch point accuracy .

---

<div class="post-metadata">

**Author:** ![TheBoatScans](https://avatars.discourse-cdn.com/v4/letter/t/b77776/32.png) [@TheBoatScans](https://forum.revopoint3d.com/u/TheBoatScans)\
**Post date:** [January 3, 2024, 10:31am UTC](https://forum.revopoint3d.com/t/miraco-far-mode-point-distance/23542/3 "2024-01-03T10:31:46Z")

</div>

Yes, I scan large things. 🙂

It would be nice if the desktop version of the software didn’t cap point distance at 2mm as well.

---

<div class="post-metadata">

**Author:** ![PUTV](https://yyz1.discourse-cdn.com/flex029/user_avatar/forum.revopoint3d.com/putv/32/15302_2.png) [@PUTV](https://forum.revopoint3d.com/u/PUTV)\
**Post date:** [January 3, 2024, 4:13pm UTC](https://forum.revopoint3d.com/t/miraco-far-mode-point-distance/23542/4 "2024-01-03T16:13:42Z")

</div>

Then you need to scan large stuff with Standard or High resolution and not use the Large option … this will change the fusing option because of the point distance .

The smallest is in High resolution mode following by Standard , Fast mode ( the lowest resolution on PC .

Try to clean the scan in raw mode on PC , too large volume will adjust the fusion settings to prevent the software from running out of RAM .

If you fused a very large object at higher resolution it will be enormous, so only computers with 64GB of RAM can handle that or you get crashed .

Sadly the PC software do not check how much RAM the computer have to allow us to fuse at higher resolution .

The principle here is that if you choice a large mode the pitch point is not lower than 2.0mm so it can’t be fused at lower than the main accuracy in that mode . Because there is no data supporting that .

Scan with Standard mode , it will give you greater results when scanning large objects and better resolution and very much usable in reverse engineering, faster mode is not , too low resolution and accuracy .